how to make a flute

Cut outside of the node and not into it. Measure the Hole Distances.

How To Make A Homemade Pvc Flute Youtube Tutorial Native American Fashion Homemade

For a flute that plays in the key of A use a 14-inch length of pipe.

. About 15 inches in length is where we think we get the best sound. Or a maker can make the flute out of two pieces of wood. The slow air chamber and the. Knock Out The Nodes.

Sand the opening to make it smoother and more pristine. You can make a native American flute out of bamboo or red cedar wood both of which should be of excellent quality without any cracks on the surface that may spoil the flute. Use the right tools you need for flute making. If you want to play your flute standing up keep your feet shoulder-width apart and firmly planted on the ground.

In order to make a Native American style branch flute you need to follow the steps. Once you make your first flute you may want to make others each time changing the embouchure slightly. Six holes provide the western seven-note scale. Shaping the root section to get the right size.

While a branch is split into two. Cut the PVC Pipe. Knowing if your flute is flat or sharp will determine how you get it back into tune. Dry and store bamboo.

Measure 5 12 cm from the end and mark. Fix a piece of well-fitting rubber into the flute and tap it a couple of times using a sledgehammer. For an F flute 18 inches and for a key of D 21 inches. Most beginners of flute making will try to construct a North American style flute out of PVC for their first flute.

Choose an appropriate raw material for the flute. This area is will be the cork while the blowhole wont be placed far from it so dont cut. Play the flutes and using the fingering charts. Left hand section with 3 keys 3 pins 3 springs 3 striker plates 3 pads two tenon corks two cork buffers and a cork dot.

Continue the line another 1 12 cm and mark again. Choose the node that will become the cork and measure 2 cm out from the node and mark it using a pencil. Weve thrown a few other items like our Blue Bear Flutes T-shirt to show your support as well as our amp if your first flute turns out to be a masterpiece and you want the world to hear it. You also may want to look at a nice flute and try to duplicate the embouchure.

It could be that the wood you use has more than one node. Continue along the line another 8 cm and mark then 7mm and mark again. You will want to make sure that your PVC pipe is the correct length. If you are making a flute out of bamboo make sure that the wood is mature and not green.

Contrary to what. Between these two marks is where the wind-way will be cut out. If you are styling the flute out of cedar then saw the wood making. The shorter the PVC pipe the higher pitch you will have and the longer the pipe is the lower the flute will sound.

Flat refers to a pitch that is slightly lower than it is supposed. Instructions on How to Make a Flute. Problem is most of the beginner makers have no clue about the potential dangers of working with PVC. Place three fingers from one hand on the top three holes and three fingers from the other hand on the bottom three holes.

The maker eithers drill a flute with long drill bits or so called gun-drill which is a modified lathe. Use the breath and its influence on the sound of the flute. The length of the pipe determines the key. Right hand section with one ring 2 keys 2 pins 2 springs 2 striker plates 2 pads 2 buffers and a tenon cork.

Grab a branch find a proper branch and dry it so that its perfect for your own flute. Hold the flute horizontal to your body and place your lips next to the mouth opening. You have to knock out all the additional nodes to enable the flute to make great sounds. Split the branch and carve the chambers split the branch in two and use chisels to carve the two inner chambers of the flute.

Then the maker creates the inner chambers. Make sure the flute is parallel to the ground rather than angling it down. Clear up the debris from the gut using a file and sandpaper. 1 barrel with two rings female slide and slide cork.

Blow over the flute. Below you will find several items both helpful to making your own Native American Flutes as well as great example flutes to use as a starter into the understanding of how they are made. Cut the bamboo flute to the length you want according to the key. The basic construction of a PVC flute is simple.

With the help of a saw cut the wood measuring 18 inches the standard length of the flute. That way you can compare embouchures. A flute that is out of tune might be flat or sharp. Many a beginner has started his flute journey with PVC.

Making the flute to the key you want. Insert a block to the correct depth at the blown end and you have a flute. The finished flute will not kill you but what is produced during the process of making the flute is what gets you. Usually a single piece of wood like 44 or 66 cm is cut into two 24 or 36 or two separate pieces are taken.

The important thing is not to change the outside shape or diameter of the blow-hole unless of course you plan to adjust the placement of the finger holes. Feel free to modify the length to your preference. One blown hole initiates the sound. Steps for Making a PVC Flute.

Homemade Instruments For Kids Flute Homemade Instruments Homemade Musical Instruments Diy Musical Instruments